In the building manual for the PT 11 it says: "The PT 11 sailing rig is designed to be light and easy to use, not to be bullet proof." In developing this rig, weight and ease of use were the biggest priorities. "Hiking (sitting on the rail and leaning out) is okay for one person to do but not two. Sailing with two and having one person hiking and the other sitting inside is okay too, just not two sitting on the rail."
The PT 11 sailing rig arrives ready to use with all of its running rigging. One small item is up to you and that is the traveler line. This is the line needed to clip your main sheet to.
You can tie a line with a little slack, using the existing holes on the transom inwale to clip your main sheet onto that. This self steering blog post shows this method.
The traveler can be be made shorter as shown below by drilling holes about 7" from the centerline (14" apart). We drilled 5/16" holes and then applied a few coats of epoxy to the walls of the holes to seal the plywood.
The traveler line can be around 3/16 diameter and be held with stopper knots underneath the inwale.
A short PT 11 travelerThis image shows the tiller/hiking stick in the self-steering position. This is good for brief periods and works best when going upwind and only works when the boat is heeled.
When sailing, if you feel resistance on the tiller, check to see if the rudder is completely down or if you have caught kelp or other debris. Keeping the threads in the knob clean and greased is important. The threads in the knob are brass and the pin is stainless steel so it will corrode. A bit of maintenance will insure the knob does its job and keeps the rudder down.
For post-2021 kits, use the forward daggerboard cap turndog to hold down the daggerboard by closing it over the hold down pin.Pre-2021 daggerboards are thicker and shaped differently at the top. A loop of line at the right length becomes a hold down when captured by the aft turndog.
The Tack clips onto the boom as shown. (This image shows an older style gooseneck.)
The outhaul (asymmetric) snap hook clips into the clew and the outhaul line should be snugged through the v-cleat on the boom:
PT 11 Outhaul configuration during a regatta. Schooner Sir Isaac in the background.
The vang clips into the eye strap on the mast.
The vang controls the twist of the sail. Controlling twist is important for getting the most power out of the sail, but don't overdo it! Some twist is good but the boom isn't un-breakable.
When adventuring or in fluky winds, we carry our oars with the oarlocks in the forward sockets and the handles tucked under the bow as shown above.
If you are new to dinghy sailing, avoid this use of a slip knot on the main sheet. Unsuccessfully yanking the slip knot free in a puff is a recipe for capsize.
If you capsize when sailing, after righting the boat, make sure the mast is fully seated in the socket before taking off again.
If you are new to dinghy sailing, it is better to start in protected waters or when there is an onshore breeze, preferably steady but not strong.
Keep your weight forward for speed, but move aft in stronger breezes and downwind sailing.
If the water is cold in your area like it is on Puget Sound, wear a wetsuit or drysuit in case you end up in the water. Hypothermia is no joke. It is always advisable to wear a life-jacket/PFD.
Learn to stall, or "park" by pointing into the wind and letting the sheet go. When the wind picks up more than you feel ready for, or you have taken water over the rail and you are feeling a little out of control, this is a good way to take stock: bail, check your rudder and daggerboard for kelp, sort out lines, and take a swig from your thermos before heading off again. The sail will flap and make noise but that is not a problem. When you are ready, reign in your sheet, and continue or head for safety.
Notice
Port Townsend Watercraft will not be shipping out anything during the month of April, 2024
This includes sailing rig drop shipments, print books, bumper, Delrin turndogs, and fillet sticks. Dinghy kit salesare through Chesapeake Light Craft and not affected by this notice.
Ashlyn, the one who prints the labels and keeps track of it all will be out of town for the month of April. While away, Russell will be building PT 11 sailing rigs along with other projects on the bench. Sailing rigs on order will be shipped starting in May.
If you order our print books or small items from our website after March 29th, they will be delayed. Alternatively, the books are available on other online book sites including Amazon. Wooden Boat Store in Maine carries them as do several outlets in Port Townsend, including Admiral Ship Supply, Edensaw Woods, and Duckworks Boat Building Supplies.
Every year we make a point of sailing in the Shipwrights Regatta in Port Townsend Bay. This event has a special history and purposefully invites our marine trades professionals to put their tools down for a day and remember why we do what we do by playing on the water.
Photo by Chance Bates
When we first entered the PT 11, we were by far the smallest boat. Not classified as a racing dinghy and of course, unable to compete with the 505s or Thunderbirds, we entered in the Cruising class. Sometimes that meant a single start in C-class of our 11 feet and up to 40 foot boats and more. Some times the C class has enough boats to divide it into 2 starts of under 30ft and 30ft plus.
As boat ownership has become more financially challenging for the working class and many of our retired marine trades people, the boats many of us own have become smaller and more often trailerable. While the economic realities of this change are frustrating, it has also meant that a larger number of smaller boast are sailing in the local regattas. The PT 11 might still be the smallest boat in the Shipwrights Regatta fleet but we are amidst more similar company which makes for some nail biting finishes!
My 2024 Shipwrights Regatta video features many of the other C-class boats as we sailed around waiting for our start. I was having trouble making my gloved fingers find the right buttons on our little waterproof Olympus and it was too chilly not to wear gloves. Several times I thought I hit record only to see recording start after I thought I had ended my shot. I gave up and just had fun.
