In the building manual for the PT 11 it says: "The PT 11 sailing rig is designed to be light and easy to use, not to be bullet proof." In developing this rig, weight and ease of use were the biggest priorities. "Hiking (sitting on the rail and leaning out) is okay for one person to do but not two. Sailing with two and having one person hiking and the other sitting inside is okay too, just not two sitting on the rail."
The PT 11 sailing rig arrives ready to use with all of its running rigging. One small item is up to you and that is the traveler line. This is the line needed to clip your main sheet to.
You can tie a line with a little slack, using the existing holes on the transom inwale to clip your main sheet onto that. This self steering blog post shows this method.
The traveler can be be made shorter as shown below by drilling holes about 7" from the centerline (14" apart). We drilled 5/16" holes and then applied a few coats of epoxy to the walls of the holes to seal the plywood.
The traveler line can be around 3/16 diameter and be held with stopper knots underneath the inwale.
A short PT 11 travelerThis image shows the tiller/hiking stick in the self-steering position. This is good for brief periods and works best when going upwind and only works when the boat is heeled.
When sailing, if you feel resistance on the tiller, check to see if the rudder is completely down or if you have caught kelp or other debris. Keeping the threads in the knob clean and greased is important. The threads in the knob are brass and the pin is stainless steel so it will corrode. A bit of maintenance will insure the knob does its job and keeps the rudder down.
For post-2021 kits, use the forward daggerboard cap turndog to hold down the daggerboard by closing it over the hold down pin.Pre-2021 daggerboards are thicker and shaped differently at the top. A loop of line at the right length becomes a hold down when captured by the aft turndog.
The Tack clips onto the boom as shown. (This image shows an older style gooseneck.)
The outhaul (asymmetric) snap hook clips into the clew and the outhaul line should be snugged through the v-cleat on the boom:
PT 11 Outhaul configuration during a regatta. Schooner Sir Isaac in the background.
The vang clips into the eye strap on the mast.
The vang controls the twist of the sail. Controlling twist is important for getting the most power out of the sail, but don't overdo it! Some twist is good but the boom isn't un-breakable.
When adventuring or in fluky winds, we carry our oars with the oarlocks in the forward sockets and the handles tucked under the bow as shown above.
If you are new to dinghy sailing, avoid this use of a slip knot on the main sheet. Unsuccessfully yanking the slip knot free in a puff is a recipe for capsize.
If you capsize when sailing, after righting the boat, make sure the mast is fully seated in the socket before taking off again.
If you are new to dinghy sailing, it is better to start in protected waters or when there is an onshore breeze, preferably steady but not strong.
Keep your weight forward for speed, but move aft in stronger breezes and downwind sailing.
If the water is cold in your area like it is on Puget Sound, wear a wetsuit or drysuit in case you end up in the water. Hypothermia is no joke. It is always advisable to wear a life-jacket/PFD.
Learn to stall, or "park" by pointing into the wind and letting the sheet go. When the wind picks up more than you feel ready for, or you have taken water over the rail and you are feeling a little out of control, this is a good way to take stock: bail, check your rudder and daggerboard for kelp, sort out lines, and take a swig from your thermos before heading off again. The sail will flap and make noise but that is not a problem. When you are ready, reign in your sheet, and continue or head for safety.
The Seventy 48 race this year was a first for PT Watercraft in that there were two PT 11's in this 70 mile event. Our local hero Inger Rankins rowed her 4th race in the PT 11 and it is interesting how every year can be so different. We will start with Inger, whose tracker never communicated to the satellite and many of her fans thought she had dropped out. Think again. While her family and friends in Norway, France, California, Virginia, New Mexico, and Port Townsend were all frantically wondering where she was, she was happily keeping her rhythm over the waves, admiring the moon over Mount Ranier, and chatting with other racers. We contacted the race boss and were told that there were technical issues with many trackers. At that point almost 60 trackers out of some 125, were not showing up on the map. I can only imagine their stress was about as bad as ours. You can read about the NWMC's tracker woes in this R2AK leg one post: https://r2ak.com/2023-daily-updates/stage-1-day-2-a-day-without-trackers/
We have faith in Inger. She had both a radio and a phone onboard that she could use if needing help and since the race committee did not contact her, she was blissfully unaware that there was a problem. When her phone rang several times however, her fingers were so stiff that she could not get to it in time to answer. She later saw that her husband and I had called. "why are they calling me?" she wondered, " Don't they know I am busy rowing?" she reasoned and did not call back. We know her enough to have guessed her thinking. 😉
As morning came, we decided we were going out to find her. We could see where team Tally Row was and that was the key to our hunt. Team Tally Row was solo skippered by Leo Sampson, also in the PT 11 nesting dinghy. We have been super happy to see him engage in this event, inspired by Inger and drawn by the challenge of the race, and we figured the two PT 11's would likely be together en-route.
We departed in our latest pod cat, 'Sipper', a sleep deprived Russell, myself, and friend and naval architect Jim Franken. We all forgot binoculars, a key tool when searching the semi open waters for an 11ft dinghy. Not to be defeated we checked in with all the racers we saw in the south end of Port Townsend Bay and through 'The Cut' bound for Point No Point where we could see Leo's tracker progressing North.
Team Tally Row near Point No Point, June 3rd.
We found him easily as you can when a tracker is working. Leo looked happy, relaxed even, after 15 hours rowing; the hard part between midnight and 2 am having been overcome. He told us that Inger was ahead of him by at least an hour. He knew this because a SUP boarder had told him he had talked to her before he went ashore for a rest and then had caught up with Leo. Well, that meant, we had totally missed her! "Tell me when you find her!" shouted Leo, as we pulled away.
It was around this time that our motor starting missing and floundering. Uh oh... Can we even make it back ourselves? I message Diana Tally an update. "Don't worry, Inger can tow you home!" says she. Well, we'd have to find her first. 😉
We buzzed and coughed and nursed the motor back towards Port Townsend, this time closer to the coast. Again under the bridge connecting the peninsula to Indian Island and still no Inger. 'Go towards the Mill,' says I. 'But what if she is on the other side?' says he. 'No way,' says I. And then we see the Race Boss boat zoom towards the Mill and way off in the distance, come to a wake-making halt. 'They found her!' says he and we make haste in that direction. Why had we not brought binoculars?! The phone rings. Sean, Inger's husband calls to say he can see her from the bluff at the end of Sheridan street. ' She's approaching the Mill,' He had his binoculars... !
Finding our lost sheep; Team Valhalla June 3rd in Port Townsend Bay.
The morning sun reflecting off the bright white transom of the PT 11, and the glossy flashes of the wet carbon oars were the first real recognition of our tiny target. We sure are happy to see you! says we. and happy to see you too, say she. We give her an update on the situation and make sure she is alright and begin our list of calls and messages to all awaiting news. Sean does the same and the international grapevine is buzzing. Our lost sheep has been found!
We leave Inger to do what she does best just as the wind is beginning to increase against her. We know she will make it before it really pipes up but our hearts go out to Leo and all of the other racers who will hit that wind head on. It turned out to be really tough for those boats and very few, including Leo, persevered to the finish line but it set them all back by hours.
Inger arrived after 18 hours and 40 minutes of rowing, besting her previous record by almost an hour. Leo pulled in just before dark, stiff but smiling bravely 7 hours later. Two amazing achievements for these two non-athletes who trusted the PT 11 enough to carry them home over 70 miles of tricky water. We are deeply humbled and grateful to both Inger Rankins and Leo Sampson for that trust and the spirit to validate it.
Below are some photos of racers from the morning of June 3rd. Teams can best be identified by comparing with the team descriptions on the Seventy48 website.
Leo Sampson rowing the PT 11 as Team Tally Row # 111 in the 2023 Seventy/48 race from Tacoma to Port TownsendInger Rankins rowing the PT 11 as Team Valhalla # 119 in the 2023 Seventy/48 race from Tacoma to Port Townsend, in Port Townsend Bay June 3rd.Team Dutchess of Desire (Patrick Kinghill) 2023 Seventy48 2023Erica Lichty - Team SEASTR in the 2023 Seventy/48Seventy/48 2023 Team SolveigSeventy/48 2023Seventy/48 2023Seventy/48 2023 Team Big Deck EnergySeventy/48 2023Seventy/48 2023Seventy/48 2023Seventy/48 2023 Team Man SpeedSeventy/48 2023 Team Splinter AmbassadorSeventy/48 2023Seventy/48 2023Seventy/48 2023Seventy/48 2023 Team Dumas Bay BrethrenSeventy/48 2023 Team Where's My HatSeventy/48 2023Seventy/48 2023
Post Script for a giggle...
Due to the fact that Inger's tracker did not communicate until the very end of the race, the map tracking showed Team Valhalla as "first overall"!! .... seriously, wouldn't that be amazing? Especially the data saying she traveled the ~70 miles from Tacoma in 1 minute and 27 seconds!
A confused tracker map....
I suspect she wiggled her nose or twirled her ponytale and teleported...
"And Don't forget the beer!" ( the below video clip sound won't play.. The audio has Russell and Sean discussing if they have enough beer for when Inger reaches the finish.)
I tried to load these to Instagram but they all look blurry. I will just load them here and if anyone wants better copies, let me know. It was a perfect and beautiful morning for the start of the race. Fewer boats than usual but it was fun to be on the water with everyone.
Friday and Saturday the Seventy/48 human powered race happened and once again Inger Rankins (Team Valhalla) blew us all away in the PT 11. But there were two PT 11's in that race and I will put together a dedicated post about that.
This September we had the opportunity to play with an EP Carry electric motor for the first time. Dinghy owners often ask about an outboard for the PT 11.
Our preference is to discourage outboards on our dinghies because good rowing and sailing boats never make great motor boats. But some people really want to be able to use an outboard. That's understandable, but the fact is that the smallest gas outboard motors currently available are really too big for our boat; too much power and too heavy.
Now there is an option we can support; the EP CARRY electric "outboard". All of the technical information about this innovative little motor can be found on the website ELECTRICPADDLE.COM. Though it is compared to a 1HP on their website, it has sufficient power to get the PT 11 up to a cruising speed of about 4 knots. The USCG however, considers all small electric outboards as "2HP". Based on that formula, the PT 11 and PT Spear are rated for "2HP" so, the EP CARRY aligns with the Coast Guard figures. The amazing thing about this motor is that it weighs only 14.4 Lbs. This makes it very easy to mount and remove. The battery pack weighs 6.3 Lbs, making the total package less than 21 Lbs. There are several design features that add to the ease of handling as well.
(At this years wooden boat festival, Russell showed up with the motor in his bicycle bag.)
Our recent experience with the EP Carry was very positive and to my surprise, I caught Russell grinning after speeding off to visit other boats in the anchorage. "Mr. anti-outboard" was actually having fun and we enjoyed it further by taking a friend on an evening "cocktail" tour of Reid Harbor, a deep bay with lots of shoreline and many boats to observe.
We spent a couple of days, driving along the shore of Sucia in the San Juans, in Shallow Bay making watery doughnuts, backing up, going forward, generally goofing off, and then venturing out to 'Danger Reef' to "brave" close proximity to a group of Stellar Sea Lions. We were pleasantly surprised by how far the battery went on one charge. You will notice in our video that we carried our oars with us but we did not need to employ them.
This motor is not silent. Neither is it loud. Our lightly built plywood boat seemed to acoustically amplify the sound a little. Even so, there was no need to raise our voices for conversation. In fact, we could almost whisper and still communicate. This was a plus to me. Loud outboards in quiet anchorages are, in my mind, a real nuisance and many of us are familiar with boaters talking in their loud dinghies barely hearing each other and assuming no one else can hear them either...but of course we hear every word. Sound is a funny thing. With the EP Carry, the birds, seals, and sea lions were undisturbed by our passage. It made it a great modus for exploring the nature around us.
Another thing that is really attractive to us about this motor, is that even with our limited house battery power, we could re-charge the EP Carry Battery. It does require a 150-200W inverter, but this lithium battery requires a third of the power than comparable models to recharge. At home, it is simple to plug it into a normal outlet. Beyond charging the battery and rinsing the unit after use in salt water, there is virtually no maintenance. Yet another plus.
(see our video exploring Sucia with the EP CARRY)
When our EP Carry arrived at the door, unpacking it was quite amazing. The care taken to pack it and the detailed contents made for a well thought out and complete package. It was a positive reflection of Joe and Linda who have spent years perfecting their product. They, like us, had a vision that they worked and reworked in every detail. In fact, the original mount did not fit the PT 11 and now it does. Further, the EP Carry, designed right here in WA State, is assembled in the USA. It is yet another example of admirable American ingenuity with style and a small business making a positive difference in the world. Of all the outboards on the market, we feel confident that the EP Carry is a good fit for the PT 11.
Sunday, March 24th was an overcast and cold day to be out on the water. Russell was not deterred. Paul Bieker's new design (the Riptide 41;"BLUE") was in the water and Russell was invited to check it out. "BLUE" is one of the most innovative racing sailboats around and sailed almost 23 knots on her very first sail. { read more about it. }Bieker Boats design team of Paul Bieker and Eric Jolley are responsible for designing our PT Skiff, the 18.5ft fuel efficient motor skiff kit, sold by PT Watercraft. The PT Skiff, "Pika", built by J. Brandt in Seattle, was also there to compliment the gathering. While on the dock at Shilshole Marina, a wedding party came down the dock and the bride and groom asked for a ride in the PT Skiff. Jan obliged and the smiling couple posed for photos. Russell snapped a few along side the wedding photographer. The PT Skiff has been put to work as a regatta chase boat, a marine research commuter, a phototgrapher's platform and now as a wedding prop!Since we sold our PT Skiff, .., we have been using our experimental tornado cat motor boat for any over water commuting. The 'Grasshopper" (as we sometimes refer to it) has many many miles on her 15hp motor. The trip from Port Townsend to Seattle takes about 2 hours and generally uses about 2 gallons of fuel. This boat was designed on the back of an envelope and it is definitely a unique boat. No, there are no plans available.. Russell was able to surf a cargo ship's wake for about 10 miles before the intensity of it got to him and he exited the wake. The trip from Port Townsend to Seattle and back, with favorable currents and surfing, used about 3 gallons of gas. This short video does little justice to the fun he was having.
This last summer we drove the skiff across country and had some opportunities to splash in the Atlantic and Chesapeake. Alas, my video skills are not too hot. I compiled some of the better clips from the summer in this video. http://www.youtube.com/watch?v=EpJoJfkA0j0
I would like to mention that Russell has been working on the nesting dinghy design and we hope to start a blog for it soon. Cheers.
On September 15th, as the City Hall tolled 9:00am, Russell and I were pulling out of Port Townsend Harbor in the PT Skiff. We were loaded up with nearly 600 lbs between the 2 of us and gear. It was foggy and cold on Puget Sound but that is nothing new.
We were headed for Desolation Sound BC to visit friends with a new baby. We had not devised a dodger and the weather was questionable but we were happy to be off on an adventure even if it was just for the short time we had available.
We spent 8 days total on our trip, camped ashore every night, travelled some 360 miles at an average of 15knots, and burned about 30 gallons of gasoline. We did prepare an option for sleeping onboard but never needed it since campsites were plentiful along the way. We got caught in the rain once between Ganges and Wallace Island but we had our foul weather gear and watertight bags.
Russell napping on the forward sole
The only semi rough water we encountered was East of Nanaimo and even that was mild. We didn’t even have to slow down, though trying to hand hold the camera steady enough to show the gps was a real trick. I will be putting together a short video of that day, surfing the Navy’s wake and Dodd Narrows.
beautiful day in Desolation Sound
The biggest threat of the trip was the raccoons!
'face-off'
On Wallace we had to tie our food bins up between 2 trees and chase the critters off, but our last night out on Jones Island in the San Juans, we were slack and the coons got into everything, devouring all the food we had left and making a disastrous mess in the boat and on the dock. We could have kicked ourselves. We mourned our stupidity over breakfast at Rocky Bay Cafe in Friday Harbor.
raccon prevention
The other difficulty was not having a tide chart with us. We had wanted to tie up at the very end of Sturt Bay on Texada but decided the risk of getting stranded in the morning low tide was too big. We tied the boat just south of where we had floated over a good 5 feet of water. The tune of rapids woke us before daylight and in the morning the whole area was high and dry. Our precaution paid off and the skiff still floated in a foot of water outside of the channel and we were free to continue our trip.
Sturt Bay lagoon
All the way home we had current against us but being able to hug the shore and make use of back eddies gave us a knot + on our speed.
riding the back eddies
It was a beautiful trip that climaxed at our friends homestead near Quadra. Add to that, fresh fish and a campfire dinner, hunting Chantrelle mushrooms and enjoying the amazing wildlife of BC at close range, such are the things that made the trip extremely memorable. The skiff made it easy to get away on short notice and return home in a short weather window.
August 8, 2010 is now marked on the calender as the first PT Skiff rendezvous. PT Watercraft and "Pika" met in Puget Sound and compared boats and notes and each took turns at the wheel of the other. Paul Bieker and family happened to be Seattle bound on their boat which provided a great photo platform and we were able to get some video. The PT Skiff Rendezvous 2010
Pictured here you will see the "Pika" powered with Evinrude's E-Tec 25hp. We are working on a fuel consumption study and comparison for the two boats to be published soon.
"Pika" has her driver's seat and grates held snug with velcro to great effect. Furthermore, the builder opted for a larger forward hatch. He also kept the side decks clear finished and the wood grain looks really nice next to her "20 feet of Bahama water"-blue hull paint.
Of his return trip, the owner of PIKA wrote:
"Not sure if you guys noticed the large Hapag Loyd container coming down the sound as we split. He was running at 20 kn and I took his stern by about 100 yards and got on his east side a bit north of Point-no-Point. He had an awesome wake and I ended up surfing and carving sweet bottom turns for 5.5 miles until I had to bail out for Edmonds. Now, THAT is more fun than you are allowed to have in a powerboat! Truly the surfing was just brilliant. Everything came together perfectly, flat water, lot's of space, and a big ass container ship running at 20 kn in the right direction. Who knew the skiff would bottom turn like my 9'6" longboard, over, and over, and over again. I am still grinning!"
We are on the road to the east coast and somehow these photos did not upload right on the website so I am posting them here. When we get back I will be able to make such updates from the main computer. Here is the windshield photo and a photo of a hatch with the watertight gasket and custom machined turn-dogs installed. These photos relate to the kit details page linked from the PT Skiff page of the website (or click on the photo here in) and are options available in addition to the base kit. Thank you for your patience! Best to all, Ashlyn & Russell.
Plexiglass windshield with adjustable height on a welded stainless bar.Installed watertight hatch
.., we have been using our experimental tornado cat motor boat for any over water commuting. The 'Grasshopper" (as we sometimes refer to it) has many many miles on her 15hp motor. The trip from Port Townsend to Seattle takes about 2 hours and generally uses about 2 gallons of fuel. This boat was designed on the back of an envelope and it is definitely a unique boat. No, there are no plans available.. 
